My Cart
You have no items in your shopping cart.
Compare Products
You have no items to compare.
Recently Compared Products
- MITSUBISHI 1990-1994 Eclipse / Talon (AWD Only) 650HP Level 2 Front Axles
- CHEVROLET CORVETTE 2005 ONLY C6 Automatic with 4L60 Trans 3.375” Carbon Fiber Shaft(Torque Tube)12mm bolts
- CHEVROLET CORVETTE 1997-2000 C5 6-Speed Manual 3.5'' Aluminum Heavy-Duty Driveshaft (Torque Tube) 10mm bolts
- HONDA 1998-2001 Accord 4 Cyl 5-Speed Basic Axle Level 0
- HONDA EG/EK (with ABS hubs) B-Series 600HP Level 3.9 Axle/Hub Kit
Recently Viewed Products
- CHEVROLET CAMARO 1970-73 500HP Steel Driveshaft 500hp10-Bolt Rear / 700R transmission
- R35 Rear axle Stubs for the GTR (For NI66 Kit)
- FORD 2011-12 Mustang V6 5-speed manual 3.5" 1-Piece with CV Aluminum Driveshaft
- VOLKSWAGEN 1999-2005 Golf / GTI / Jetta / Beetle (VR6 / 1.8T) 5-Speed Manual (exc. 337 chassis) 500HP Level 2.9 Axles
- 2004-2011 GTO / G8 / Camaro / CTS-V conversion plate
Product Description
GTOSH2 1200HP 1-Piece Aluminum Driveshaft
Now with a direct fit rear flange, eliminates the billet aluminum adapter plate!!!!!
The 3.5" aluminum single piece driveshaft is a direct bolt-on system. Most driveshafts available for the GTO platform require the rear flange to removed from the diff, the problem with this is that the differential is a crush collar type, and the preload on the nut sets the pinion depth to make sure the rear gears have the proper engagement. What we have done is made a 7075-T6 aluminum conversion flange that will bolt directly to the 3 finger flange on the rear But now has Helicoils in the threaded section of the billet plate(same style we make for the 1000HP Supra shafts). This eliminates the need to have a professional set the pinion lash on the differential. Just unbolt the factory 2 piece shaft, install the 1-piece shaft with the included hardware and go. The only necessary modification is the tip of the rear seatbelt bolt that protrudes into the driveshaft tunnel must be ground down to provide adequate clearance for the driveshaft. Changing the shaft in this car is perhaps one of the most noticeable performance enhancements you can do as the car will have better throttle response and feel smoother overall. Not only is it lighter but the hanger bearing on the factory driveshaft moves up and down violently when the car is being driven hard. This action is not only dangerous but robs the drive train of power. Capable of 997lb of torque based on shock factor of 3.5 .
Now with a direct fit rear flange, eliminates the billet aluminum adapter plate!!!!!
The 3.5" aluminum single piece driveshaft is a direct bolt-on system. Most driveshafts available for the GTO platform require the rear flange to removed from the diff, the problem with this is that the differential is a crush collar type, and the preload on the nut sets the pinion depth to make sure the rear gears have the proper engagement. What we have done is made a 7075-T6 aluminum conversion flange that will bolt directly to the 3 finger flange on the rear But now has Helicoils in the threaded section of the billet plate(same style we make for the 1000HP Supra shafts). This eliminates the need to have a professional set the pinion lash on the differential. Just unbolt the factory 2 piece shaft, install the 1-piece shaft with the included hardware and go. The only necessary modification is the tip of the rear seatbelt bolt that protrudes into the driveshaft tunnel must be ground down to provide adequate clearance for the driveshaft. Changing the shaft in this car is perhaps one of the most noticeable performance enhancements you can do as the car will have better throttle response and feel smoother overall. Not only is it lighter but the hanger bearing on the factory driveshaft moves up and down violently when the car is being driven hard. This action is not only dangerous but robs the drive train of power. Capable of 997lb of torque based on shock factor of 3.5 .
